Home Products Q&W Proximity Sensor Color SensorHW50-W Color Sensor

HW50-W Color Sensor

1. The installation dimensions are consistent with those of the international brand Diens and can be directly interchanged
2. The push-button operation facilitates work efficiency
3. The plug-in connection cable facilitates installation and maintenance
4. The working status is clearly visible with an indicator light

Get a Quote

Technical Parameters

HW50-W Color Sensor

Parameter
Supply voltage	10...30VDC
Power ripple	Max:2vpp
Power consumption (exclude current output)	Max:50mA when is 24Vcc
Output signal	PNP and NPN
Output current	Max:100mA
Output saturation voltage	≤2V
Response time	33μs
Switch frequency	15KHz
Delay	0/20 optional (factory set to don't delay)
Status indicator	Output indicator (green),ready indicator(yellow),delay indicator(red)
Press button	"MARK" button, "BKGD" button
Liangton/Antong option	Automatic (factory setting is Liangton mode)
Work temperature	-10...50℃
Storage temperature	-20...70℃
Dielectric strength	500Vac/minute, between appliance and shell
Insulation resistance	>200MΩ 500Vdc, between appliance and shell
Detection distance	10mm±3mm
Min spot size	1.5x5mm when is 10mm
Light source type	Blue (465nm) Green (520nm) Red (630nm) Auto selection
Ambient light inhibition	According to EN60947-5-2
Shaking	0.5mm amplitude, 10...55Hz frequency, all direction（EN60068-2-6)
Impact	11ms(30G),6 impact, all direction (EN60068-2-27)
Shell material	ABS
Lens material	PMMA
Mechanical protection grade	IP67
Connection type	Pin Connector
Weight	Max90g

Control Panel

• Output indicator light (Green)

Green light shows output state

• Ready indicator light (Yellow)

Yellow light shows normally on shows it work normally in the cause of work, if twinkle quickly means ovierload output.

• Delay indicator light (Red)

Red light on means delay function is activiated .

• Mark Button

It starts to teach the color mark when press the "MARK" button.

• BKGD Button

It starts to teach the background when press the "BKGD" button.

Setting

Detection（Mark---Background）
1. Set the color code in front of sensor light, Press "MARK" button till YELLOW light off.
•Sensor will use red green
and blue light interaction to test the color code.Please don' t move the color code during this period.
2. Set background color in front of sensor light, Press "BKGD" button, sensor will use red green and blue light interaction to test the background color, please avoid the movement of background color during this period..
•Sensor can choose Liangtong or Antong operation mode automatically, regard dark color as color mode,regard light color as background to et timing as Antong mode. Regard dark color as background regard light color as color mode to set timing as Liangtong Mode.
•If Yellow light keeps light after do the above the operation, then setting is succeed.
•If yellow light twinkles slowly ,then setting failed ,because that mark code and background don' t have enough contrast.

Delay Setting Function
• The shortest output output can be extended to 20ms, can be connected to the speed control and detection system to detect the short pulse • Red light' s on or off can judge if the delay function is activiated.

• Activiated Delay FunctionPress "MARK" and "BKGD" at the same time for 2s, till red light is on ,then delay function is activiated • Dancle Delay FunctionPress "MARK" and "BKGD" at the same time for 2s, till red light is off then delay function is activiated • Output OverloadWhen digital output is overloaded. Ready light will inform worker by twinkling slowly.
	EX- \|\| -3D T6Temperature grade: T6（<85°C）Max power consuption: 1500mW when is 30VdcMax Internal capacitance: 750pFInternal inductance: could ignore

Connection mode

Installation
Three sides of color mark sensor has open holes with M5x6, after adjusting the distance please don't use the torsion more than 2.2Nm when lock the screw .
We only need to change the lens plastic cap and eyeglass and could choose to test from front and side .
Dsitance from lens to inspection face must be the same with eyeglass,to achieve the max detection sensitivity.
Lens should be in 90 degree vertical plane state with detection face under normal circumstances.
It it is detection for strong light reflectivity material suggest inclines the detection angle to 5 to 20 degrees, and do appropriate adjustment according to the testing material and moving direction. See figure below :

External Dimension